GR Yaris Suspension Secrets Seat Lowering Bracket

Ok then 👍
C8EB5977-4A2A-47BD-92D8-FF1690D3C6B6.webp


78AFD55A-C321-4485-9CE2-1D792BE33F53.webp


2AC82723-1728-48AF-8AF2-D2AD86582851.webp
 
I like them a lot! Are they height adjustable? Much lower? How many £?

Most important are you happy with them, which is what really counts!
 
My lowering plate came today. How on earth have you guys installed the rear bolts?!
Any tips?
Took 5 mins to remove seat and install lowering plate. Then spent nearly a hour trying to fit the back bolts. I've just given up and come back in house.. Maybe try again tomorrow haha
 
Hi Dan,

Yes they are a pita.

I managed to pull the drivers side seat trim out enough with one hand to a get a ratchet on that one.

The rear left bolt as you sit in the seat is the difficult one, with the seat raised to its maximum you can just get a ratchet down that side under the seat but it takes a fair few goes before you are able to latch on to the bolt.

Its the old saying, if at first you don’t succeed try again, tomorrow is another day good luck 👍
 
My lowering plate came today. How on earth have you guys installed the rear bolts?!
Any tips?
Took 5 mins to remove seat and install lowering plate. Then spent nearly a hour trying to fit the back bolts. I've just given up and come back in house.. Maybe try again tomorrow haha
I got mine by pumping the seat up as high as poss and reaching in from the front was pretty easy. I didn’t have to remove any trim etc as the instructions say
 
Hi guys, FWIW I am testing an alternative pretty soon, should have a video of it within the few weeks. Similar design, loses the sliders and drops the seat a good way. Will update when I have more info (y)
 
Hi guys, FWIW I am testing an alternative pretty soon, should have a video of it within the few weeks. Similar design, loses the sliders and drops the seat a good way. Will update when I have more info (y)
What one? I have ordered a dna kit that lowers but keeps the sliders will report back once I receive it and fit from @Micloi 👍🏻
 
Is the 35mm height reduced measured from the seat pumped up or down? It says the to leave the seat pumped up after installation but is that not going to be higher than when the seat is pumped down on the sliders?
 
Is the 35mm height reduced measured from the seat pumped up or down? It says the to leave the seat pumped up after installation but is that not going to be higher than when the seat is pumped down on the sliders?
You don’t have to have the seat pumped up if you unclip the airbag plugs from under the seat.

The only reason to pump it up is in setting 1 (the only setting without spacers installed) to stop
The plugs being crushed

Even pumped up to clear the plugs in the normal fixings it’s massively lower than standard. Easily 35mm lower. Position 1 doesn’t use the 5mm spacers so take that into account.



I unclipped my plugs and moved them Out of the way and have it as low as possible. It’s so low that the plastic side trim touches the carpet now
 
You don’t have to have the seat pumped up if you unclip the airbag plugs from under the seat.

The only reason to pump it up is in setting 1 (the only setting without spacers installed) to stop
The plugs being crushed

Even pumped up to clear the plugs in the normal fixings it’s massively lower than standard. Easily 35mm lower. Position 1 doesn’t use the 5mm spacers so take that into account.



I unclipped my plugs and moved them Out of the way and have it as low as possible. It’s so low that the plastic side trim touches the carpet now
Is position 1 right back?
 
Is position 1 right back?
Yes it’s the furthest back but it’s not much more than standard looking at how close it is to the rear bench there can’t be much in it

In this position there’s loads more leg room and pedals are a better angle
 
Can somebody please measure the distance between the seat fixings as they sit on the plate? As in the distance between the holes used.

I am trying to understand how the height is reduced? A pumped up seat is about 40mm from the roof (headrest) and a pumped down seat is about 85mm from the roof so even with reducing the height by 35mm the seat would still be 10mm higher?
 
Can somebody please measure the distance between the seat fixings as they sit on the plate? As in the distance between the holes used.

I am trying to understand how the height is reduced? A pumped up seat is about 40mm from the roof (headrest) and a pumped down seat is about 85mm from the roof so even with reducing the height by 35mm the seat would still be 10mm higher?
You are removing the runners which are a good 35mm thick. You don’t need to pump the seat up as I previously posted


In the seats lowest setting the plastic side trim next to the pump handle touches the carpet and then more if you keep lowering so measure the distance between the bottom of the plastic and the carpet and that’s what you are losing in reality
 
You are removing the runners which are a good 35mm thick. You don’t need to pump the seat up as I previously posted


In the seats lowest setting the plastic side trim next to the pump handle touches the carpet and then more if you keep lowering so measure the distance between the bottom of the plastic and the carpet and that’s what you are losing in reality

Its in the instructions that you leave the seat pumped up, that's why I was wondering where the claimed height drop comes from.

I will have a look at that plastic and the gap, thanks. Does any other parts foul? The airbag plugs were mentioned? Anything else?
 
Its in the instructions that you leave the seat pumped up, that's why I was wondering where the claimed height drop comes from.

I will have a look at that plastic and the gap, thanks. Does any other parts foul? The airbag plugs were mentioned? Anything else?
Yes the instructions recommend pumping the seat a few times to prevent crushing the plugs but if you remove them from the underside of the seat you don’t have to do this

The 35mm quoted takes this into account as position 1 doesn’t require the 5mm spacers to clear the frame to car bolt heads

It’s easily 35mm drop if not more

Like I say measure from the bottom of the plastic to the floor and that is what you drop and then more on top if you keep going



My opinion you don’t want to go any lower as the recess in the door card is in the wrong place and there’s nowhere to put your elbow.

I had aftermarket seats and were 75mm lower but I had nowhere for my right arm after fitting them so sold them
 
Back
Top