GR86 Tyre pressures

What tyre pressures do you run?

  • Manufacturer (35psi)

    Votes: 24 46.2%
  • 34psi

    Votes: 1 1.9%
  • 33psi

    Votes: 4 7.7%
  • 32psi

    Votes: 22 42.3%
  • Above 35psi

    Votes: 1 1.9%
  • Less than 32psi

    Votes: 0 0.0%

  • Total voters
    52
35 - Probably best grip efficiency/economy on the road, easy to overheat the tread on track 😁
 
Mine claim to be 2.6 bar which is how it came from the dealer.
I've not checked them yet to see how accurate that is, but it seems quite high at almost 38psi.
I've only done 100 miles, ride is not bad, firm but comfortable. Quite noisy though.
 
2.2 bar or roughly 32 psi cold

2.4 cold loses a lot of grip and quickly overinflat itself when driven fast, gets to like 2.8bar after a quick B road drive. 2.2bar gets to 2.4bar in the same conditions.
 
I started at 35psi (2.4bar?). Factory spec, and always ran the previous car at that. However, I decided to drop to 32PSI and feel like its perhaps a little more compliant and planted and might help reduce the slight understeer. I also need to pull my finger out and ring Abbey to get it booked in for an alignment and maybe some camber bolts, as most seem to recommend.
 
I settled on 32 (2.2) all round on an entirely subjective basis in that I prefer the way it rides, streets and handles that way.

It feels more supple and compliant than the standard pressures.

Given that I never drive the car anywhere near fully loaded I don't see the need to use the standard pressures which will have been decided on for safety under the most extreme fully loaded conditions.
 
I settled on 32 (2.2) all round on an entirely subjective basis in that I prefer the way it rides, streets and handles that way.

It feels more supple and compliant than the standard pressures.

Given that I never drive the car anywhere near fully loaded I don't see the need to use the standard pressures which will have been decided on for safety under the most extreme fully loaded conditions.
Exactly this for me too.
 
I've done the opposite actually, about 2.4 cold gets up to 2.6/2.7 sometimes and feels a bit more agile/darty and playful. I am on different tyres though, which provide a bit more feedback, but are noisier.

Horses for courses

Edit: just seen oem recommendation is 2.4 (assume cold) anyway!

Sent from my Pixel 6 Pro using Tapatalk
 
Last edited:
Still playing with the settings. After testing a different tire pressure I return to the manufacturer recommendation = reeference pressure, I voted manufacturer.

Bye for now Fred
 
They do seem very highly pressured for a relatively lightweight car. Especially with quite skinny tyres.

Only comparison I have is my GT-Four which runs 30PSI cold and goes up to 32PSI when warmed up. On track I go even lower to 28PSI which goes up to 32PSI.

I would say 32PSI is a good pressure to aim for hot and is about right for the weight of the car.

Is there anyway to change the readout to PSI at all? Maybe in techstream? I only use bar as a boost measure.
 
Last edited:
Is there anyway to change the readout to PSI at all? Maybe in techstream? I only use bar as a boost measure.
I've had a look but didn't find any way to change it, no. Suspect that maybe there's a regional setting somewhere that sets it.

 
I've just dropped mine to 32psi this evening.. Just to see what the tyre noise is like

If it's no different that it was at 35psi I might go back up
 
OEM recommends 2.4 bar / 35 psi cold.

I've been running 2.4 bar / 35 psi cold. Probably increases to 2.5/2.6 bar when heated.

May try running 2.2..... to increase to 2.4 when heated to see the difference.

There is no way to show pressures in psi in the UK. Apparently. GRrrr h ;-)

I am on the OEM Michelins....

PXL_20231022_095320396.webp
PXL_20231022_095347005.webp
 
2.2 cold I run mine at but set them a while ago so in this cold weather it's 2.1ish when starting but top of road it's 2.2, then 2.3-2.4 once I'm at work. I find it better.
 
Thread resurrection time!

Having changed out the OEM (7.5") rims for 8" ones and swapped the 215s for 225s, I've been wondering what would be the best inflation pressures on the GR86? It seems to be quite a subjective matter, but the general consensus is wider tyres=less pressure. Today has seen me throwing numbers into an online Tyre Data Calculator to see what it came up with. It would seem that for better comfort I should probably go for anywhere between 32-34 psi (2.2-2.3 bar), which is between 1-2% less than OEM. Anybody else played with this calculator? My issue is that any time that I set a lower pressure than the recommended 35psi, the bloody dashboard warning comes on all the time telling me I have 'low pressure' ... :mad:
 
Last edited:
2.2 bar is what I've stuck to. When they warm they sit nicely at 2.4 bar. If you set them to 2.4 bar cold, do the sensor reset, then I drop them with a gauge.
 
Thread resurrection time!

Having changed out the OEM (7.5") rims for 8" ones and swapped the 215s for 225s, I've been wondering what would be the best inflation pressures on the GR86? It seems to be quite a subjective matter, but the general consensus is wider tyres=less pressure. Today has seen me throwing numbers into an online Tyre Data Calculator to see what it came up with. It would seem that for better comfort I should probably go for anywhere between 32-34 psi (2.2-2.3 bar), which is between 1-2% less than OEM. Anybody else played with this calculator? My issue is that any time that I set a lower pressure than the recommended 35psi, the bloody dashboard warning comes on all the time telling me I have 'low pressure' ... :mad:
It shouldn't do if you reset the TPMS after setting the desired presure.

I run 32 psi cold, - 2.2 bar. usually goes up to 2.4 when driving, much more when on the track where I drop the presure down to correct.

Always get a flat tyre warning the following morning!
 
Back
Top