GR Yaris “Engine Maintenance Required - Visit Your Dealer”

I bet they bent the pressure tube and now the car thinks GPF is blocked.
 
Does your decat pipe have both pressure and AFR sensors as the one we have fitted just has the pressure pipe removed and open to atmosphere.
On the Cobra de cats all 3 sensors are retained.
 
470C1E92-3119-462B-8E8C-CBDCE23C7E47.webp
 
Does your decat pipe have both pressure and AFR sensors as the one we have fitted just has the pressure pipe removed and open to atmosphere.
On the Cobra de cats all 3 sensors are retained.
It's not decat Richard, it's this thing - https://turbozentrum.co.uk/HJS-ECE-Tuning-Downpipe-Toyota-Yaris-GR-EURO-6 - but I've no clue what sensors it uses. Hopefully someone who knows better can chip in with details.

I've finally got hold of my local garage who are kindly sparing some time to get it on the ramps later today. I'll post the photo when I have it.
 
Well I'm at the garage now and the tube is not connected to anything. From below:-

IMG_20220128_103913.jpg


And from above:-

IMG_20220128_105619.jpg


There is also a tube with a zip tie that looks like it came off this pipe. Should we reconnect this?

IMG_20220128_110011.jpg


I've called the installers and sent these photos over. They confirm these pipes should be connected so my mechanic is now doing that.

Connection is proving difficult as the rubber pipes needs to stretch, but he's just found that the pipe in photo 1 was slid very far over the metal tube from the cat so he's moved that off a bit and it should be sorted very shortly 🤞🤞

IMG_20220128_110011.webp
 
Last edited:
Well I'm at the garage now and the tube is not connected to anything. From below:-

View attachment 1487

And from above:-

View attachment 1488

There is also a tube with a zip tie that looks like it came off this pipe. Should we reconnect this?

View attachment 1490

I've called the installers and sent these photos over. They confirm these pipes should be connected so my mechanic is now doing that.

Connection is proving difficult as the rubber pipes needs to stretch, but he's just found that the pipe in photo 1 was slid very far over the metal tube from the cat so he's moved that off a bit and it should be sorted very shortly 🤞🤞
We always cut out about 60mm tube from the OEM part (which stays with the OEM cat.) to connect them perfectly. This has a hump.
If you don‘t, you have a lot of tension on this and no hump on the cat-side part. So this rubber hose will just fall off again, no matter how tight you pull the ziptie.
 
I've just drove the long way back from the garage (25 mins) and there were no scary messages so I think this is now sorted. But I'll drive more over the weekend to be certain. I'm sure it pulls harder than before as well - it's a right beast now!

Thank you all for pointing me in the right direction 👍
 
I've just drove the long way back from the garage (25 mins) and there were no scary messages so I think this is now sorted. But I'll drive more over the weekend to be certain. I'm sure it pulls harder than before as well - it's a right beast now!

Thank you all for pointing me in the right direction 👍
So how does it feel with HJS Cat? Just curious!
 
Pleased you got it sorted! I wish HJS would include a back2back bard so we don't have to hack up a £90 OEM part.

I was speaking to mate today who just had the Enhance you car decat fitted - with no pressure tube - and he's been getting a annoying CEL/message. Thinking is that with the pressure tube to atmosphere the ECU tune is out of range. Also, with the pressure tube blocked we're worried the ECU might over fuel as it tries to regen the OPF.

TLDR, maybe the EYC decat need to be revised to include the pressure tube take off.
 
Last edited:
I wasn't aware of the EYC decat but it says "This product is design for motorsport and off-road use only. Removing the cat will require an ECU map to clear EML light." on the page I just found so it sounds like there's not much he can do.
 
So the scary message came back last night, just as I was briskly leaving a roundabout and accelerating up a sliproad while thinking to myself "good god what a car this is!" I then hear the big bong from the dash and I see "Engine Maintenance Required" on the dash!! 😭

I've checked under the bonnet and the pressure pipe looks connected but I'm going back to my local garage tomorrow for him to check it all properly.

The extra crap thing is I'm supposed to be at Drive Limits on Monday (in Essex - over 4 hours from me) for the GRY meet up! I really don't want to miss that. And it wouldn't be the same if I turn up in an LS430 :LOL:

If our ECU was cracked and someone "maps this out" what does that mean?? Actually changing some engine thing or just making it so the ECU doesn't trigger the warning like mapping for decat? (i.e. this is not damaging the engine at all). Of course I'd rather not do this and would like it to work properly, I might have to put the original cat back on which would be pretty lame.
 
Have you had fault codes read from the OBD and what did it say? Standard procedure when visiting a workshop... Could also be possible it needs a reset.
Not sure on this platform, but disconnecting the battery and let it sit for say 15min could help.

Just general suggestions, I don't actually know exactly how these things are implemented on this car.
 
Back
Top