This is NOT for cars with the JBL system. It might be similar or even the same. But I haven't checked up on this.
I tapped the audio signals from the audio box that in a LHD car is under the passenger seat. This box does noise cancelling, adds the synthetic engine noises and has four built in power amplifiers. It gets the audio signal from the head unit in the dash (full speaker level voltages from the head unit) and its outputs are wired straight to all speakers. Four channels in total, front left/right and rear left/right
BEWARE:
The head unit has a built in DSP that - even when you set it's tone controls to straight - outputs a VERY uneven frequency curve. This is to compensate the very uneven frequency response of the oem speakers. See further info below in my second post! The head unit also adds a time delay to the front left speaker, this works very good but note to NOT add more delay in any DSP you install yourself if you use these signals. In a circuit pack there are no other signals to find. The JBL kit is said to have line outs though.
------
This is the pinout of the plug:
FL Front Left
FR Front Right
RL Rear Left
RR Rear Right
You preferably tap the input signals to the box (the ones coming from the headunit, they are speaker level signals) so your aftermarket systems doesn't amplify the synthetic engine noises and the noise canceling low frequency tones added (out of phase with the cabin low frequency noises). Of course this depends on what you want to accomplish and whether you have these "effects" turned on or off via Techstream or Carista.
The connector is not easy to get to but the plus side is you have all channels in one place. Alternative places are the A-pillars down in the foot wells. I don't have connector pinouts of these for you but it's all available at www.toyota-tech.eu which is where I got my info.
The audio unit is mounted to a plastic shield under the seat. To remove you unscrew two bolts on the floor, under the carpet right under the front end of your seat:
There are two connectors, one small white and one large with a black release lever. Disconnect the small one by pushing its release tab. Then disconnect the large release lever by pushing its release tab inside this square hole and pulling the lever so the large connector slides out
This is what the two connectors look like
Connect to whatever signals you want according to the pinout above. I used the splitters you can see in the picture below but they are a bit bulky here where everything is tight. The cables are one strand and there are other ways of tapping into them, solder and shrink tube, other types of splitters and so on. But it is small and fiddly and the main multi-cable is short so you have to do it all reaching halfway under the seat. Gaah...
When it comes to 12V power I chose to tap that at the battery, mainly because there was one fused connector bolt free! The bottom one in the picture is unused.
I tapped the audio signals from the audio box that in a LHD car is under the passenger seat. This box does noise cancelling, adds the synthetic engine noises and has four built in power amplifiers. It gets the audio signal from the head unit in the dash (full speaker level voltages from the head unit) and its outputs are wired straight to all speakers. Four channels in total, front left/right and rear left/right
BEWARE:
The head unit has a built in DSP that - even when you set it's tone controls to straight - outputs a VERY uneven frequency curve. This is to compensate the very uneven frequency response of the oem speakers. See further info below in my second post! The head unit also adds a time delay to the front left speaker, this works very good but note to NOT add more delay in any DSP you install yourself if you use these signals. In a circuit pack there are no other signals to find. The JBL kit is said to have line outs though.
------
This is the pinout of the plug:
FL Front Left
FR Front Right
RL Rear Left
RR Rear Right
You preferably tap the input signals to the box (the ones coming from the headunit, they are speaker level signals) so your aftermarket systems doesn't amplify the synthetic engine noises and the noise canceling low frequency tones added (out of phase with the cabin low frequency noises). Of course this depends on what you want to accomplish and whether you have these "effects" turned on or off via Techstream or Carista.
The connector is not easy to get to but the plus side is you have all channels in one place. Alternative places are the A-pillars down in the foot wells. I don't have connector pinouts of these for you but it's all available at www.toyota-tech.eu which is where I got my info.
The audio unit is mounted to a plastic shield under the seat. To remove you unscrew two bolts on the floor, under the carpet right under the front end of your seat:
There are two connectors, one small white and one large with a black release lever. Disconnect the small one by pushing its release tab. Then disconnect the large release lever by pushing its release tab inside this square hole and pulling the lever so the large connector slides out
This is what the two connectors look like
Connect to whatever signals you want according to the pinout above. I used the splitters you can see in the picture below but they are a bit bulky here where everything is tight. The cables are one strand and there are other ways of tapping into them, solder and shrink tube, other types of splitters and so on. But it is small and fiddly and the main multi-cable is short so you have to do it all reaching halfway under the seat. Gaah...
When it comes to 12V power I chose to tap that at the battery, mainly because there was one fused connector bolt free! The bottom one in the picture is unused.
Last edited:
